17 November 2026 · 6 minute read
The Pro Tools session prep checklist
Twenty minutes before a session saves an hour during it. Here is the list, in the order it should happen, whether the day is tracking or mixing.
Session prep is the part nobody films. It is also where most mid-session fumbling comes from: the bus that was never named, the click track made while the drummer waits, the clip list with four hundred unused takes from last month. Do these twelve things before anyone else is in the room and the session runs on rails.
1. Start from a template, not from yesterday
File > New and pick a session template, or make one. A template carries your I/O names, your click track, your markers ruler, your window configurations and nothing else. Save As from the last session carries all of that plus its clip list, its plug-in state and its mistakes. Keep one template per kind of day: tracking band, overdubs, mix, post. File > Save As Template puts it in the right folder.
2. Session parameters you cannot change later
Sample rate is fixed when the session is created. Bit depth and file type can be changed afterwards in Setup > Session, but files already recorded keep theirs. Match the delivery spec before the first take: 48 kHz for anything with picture, whatever the client asked for on music, 24-bit, WAV. Interleaved is fine for stereo tracks; multiple mono is what some post houses still want.
3. Name the I/O
Setup > I/O. Rename inputs after what is plugged into them, not "Analog 1-2". Name buses after their job: Drum Bus, Vocal Bus, Verb A, Delay 1. Check the default output bus at the bottom of the Output tab; a wrong default sends every new track to the wrong place. If a previous session had the names right, the Import Settings button at the bottom of the window brings them in, and Import Session Data can do the same when you pull tracks from an old session.
4. Create, name, color and order the tracks
Cmd+Shift+N opens New Tracks. The + button on the right adds a row, so one visit makes eight mono audio tracks, two stereo auxes and a master fader. Name tracks before you record anything: Pro Tools names the audio files after the track, and renaming later does not rename the files. Keep names short enough to survive the Mix window. Color by family (drums one color, vocals another) and put the families in Folder Tracks so the Edit window stays one screen tall. Track presets (right-click a track name > Save Track Preset) save a named track with its inserts and routing for next time.
5. Routing and buses
Every drum track to the Drum Bus aux. Every vocal to the Vocal Bus. Sends to the reverb and delay returns, set to minus infinity or unity on purpose rather than wherever they landed. A master fader on the main output, always, so you can see the true level at the mix bus. VCA masters for the families you will ride. Do this now; doing it with a client on the couch is how a kick ends up routed to the headphones only.
6. Groups
Cmd+G makes a group from the selected tracks. Make an edit group for the drums so a trim on the kick trims the room mics too. Make a mix group for the BGVs. Name them; "Group 1" through "Group 9" means nothing at eleven at night. Edit groups can be suspended with one click in the Groups list, so there is no cost to making them.
7. Click, tempo and meter
Track > Create Click Track puts a click with the right plug-in on it in one step. Set the tempo in the Tempo ruler or turn off the Conductor track for a free-time take. Set the meter if it is not 4/4. If the producer sent a tempo map, import it before you make markers, because the markers want to sit on bars.
8. Record setup
Pick the record mode (normal, QuickPunch, Loop) from the Options menu. Set pre-roll and post-roll in the Transport window. Setup > Playback Engine: the hardware buffer goes low for tracking and high for mixing, and you cannot change it mid-take. Setup > Disk Allocation puts the audio files on the drive you meant.
9. Markers before the first take
Intro, Verse 1, Chorus 1, Bridge, Out. Press Enter on the numeric keypad at each one. For a mix, add the markers the client's notes refer to. Markers cost nothing and save every "where was the second chorus" for the rest of the day. The full workflow is in the markers post.
10. Clean the clip list
Clip List menu > Select > Unused, then Clear. Remove, not Delete, unless you truly want the files gone from disk. A clip list with four hundred stale takes slows every search and every Import Session Data. Do it before the session, never during one.
11. Window configurations
Window > Configurations > New Configuration. Save a tracking view (Edit window, big meters, the inputs showing), a mix view, and an editing view with automation lanes open. Recall one from the numeric keypad: period, the number, asterisk. Three configurations replace most of the window dragging in a day.
12. Save a copy, turn on backups, then start
File > Save Copy In makes a self-contained copy with the audio if you need one to travel, or a dated working copy for a mix so the original stays untouched. Then Setup > Preferences > Operation > Auto Backup: enable it, keep the ten most recent, every five minutes. The one day you need a backup is the day you forgot to turn it on.
The checklist, short form
- Template, not Save As.
- Sample rate, bit depth, file type.
- I/O names and default output.
- Tracks: created, named, colored, foldered.
- Buses, sends, master fader, VCAs.
- Edit and mix groups, named.
- Click, tempo, meter.
- Record mode, pre-roll, buffer, disk allocation.
- Markers for every section.
- Clear unused clips.
- Three window configurations.
- Save Copy In, Auto Backup on.
How Pete does this
Session Pilot is a Mac app. You talk, and Punch In Pete does the Pro Tools work you describe: tracks, routing, markers, the click track, the dialogs. Most of this checklist is one sentence each.
Make eight mono audio tracks called kick, snare top, snare bottom, hat, tom 1, tom 2, OH L and OH R, color them blue, put them in a folder called Drums and send them all to a Drum Bus.
Add a click track, drop markers at 0, 16, 32 and 48 bars called intro, verse 1, chorus 1 and verse 2.
Save a copy to the client folder, audio included, named with today's date.
The track work and the markers run the instant the sentence ends, with no AI call. Save Copy In is a dialog, so Pete opens it, fills it in and drives the Save panel behind it, which takes a few seconds. He reads back what landed, from Pro Tools, after each step. Once he has done your prep once, say "my tracking setup" and it becomes a recipe that runs instantly next time with your names in it.
He does not pick your sample rate, your buffer or your bus layout. Those are decisions. He does the clicking.
Not just another bounce or session prep app. Pete is the best assistant you'll ever have.
Session Pilot launches 16 December 2026 for Mac. Everyone on the wait list gets launch pricing locked and a 14-day free trial.
Join the wait listSession Pilot is not affiliated with or endorsed by Avid Technology, Inc. Pro Tools is a trademark of Avid Technology, Inc. Menu paths refer to Pro Tools 2026.11; older versions may differ.