17 November 2026 · 6 minute read
Strip Silence in Pro Tools: the settings that matter
Four sliders and four buttons. Most people touch one slider and one button, and then spend ten minutes fixing clipped breaths. Here is what each control does and the combinations worth remembering.
Strip Silence (Edit > Strip Silence, Cmd+U) looks at a selection, finds the parts below a level, and does something to them. It is the fastest way to turn a forty-minute dialogue take into clean clips, to tighten a tom track to its hits, or to break a vocal comp into phrases for editing. It is also non-destructive: it only separates and removes clips, and Undo puts everything back.
The four sliders
Strip Threshold (dB) is the level below which audio counts as silence. Everything else depends on this one. Start at the noise floor plus a few dB: around −40 dB for a well-recorded dialogue track, −50 to −60 for a quiet booth, −30 or higher for a tom track where you only want the hits. Watch the rectangles that appear over the waveform as you drag; they are the clips you will keep.
Minimum Strip Duration (ms) is how long a gap must be before it is treated as silence. Set it short and a breath between two words becomes its own gap and the word gets chopped into syllables. Set it long and short pauses survive inside one clip. 500 ms is a sensible start for dialogue; 50 to 100 ms for drums, where the gaps are real.
Clip Start Pad (ms) extends each kept clip earlier. This is the slider that saves consonants. The "t" in "today" sits below most thresholds; a 20 to 50 ms start pad keeps it. For drums, 5 to 10 ms keeps the transient's first wavefront.
Clip End Pad (ms) extends each kept clip later. Reverb tails, breaths that trail off, the ring of a tom. 100 to 300 ms for dialogue; longer for anything with a room in it.
The order to set them: threshold first until the rectangles cover the words, then minimum duration until the rectangles stop splitting mid-phrase, then the pads until nothing sounds clipped on playback.
The four buttons
Strip separates at the boundaries and removes the silent parts. You are left with the clips you saw. This is the normal choice.
Extract is the opposite: it keeps the silence and removes the sound. Use it to pull room tone out of a dialogue take. Set the threshold so the rectangles cover only the lines, press Extract, and what remains is clean fill you can consolidate into a tone file.
Separate cuts at the boundaries but removes nothing. Useful when you want the clip boundaries for naming or clip gain but need the gaps to stay for timing, or when you are about to run Clip Gain or Batch Fades on just the loud parts.
Rename opens the Rename settings: a base name, a starting number, zero padding, a suffix, and whether the names apply to the clips, the files or both. Set it before you Strip and every new clip comes out as Sc12_Dialogue_001, _002 and so on, instead of forty copies of the take name with hyphens.
After the strip: fades
Stripped clips have hard edges. Select all the new clips and press Cmd+F to open Batch Fades. Give every clip a short fade in and out (5 to 10 ms for dialogue, 2 to 5 ms for drums) and let the dialog adjust existing fades. Without this step the strip will click on playback and you will blame the threshold. It was the fades.
Three settings to remember
| Material | Threshold | Min duration | Start pad | End pad | Then |
|---|---|---|---|---|---|
| Dialogue, good booth | −45 dB | 500 ms | 30 ms | 200 ms | Strip, Batch Fades 8 ms |
| Toms and percussion | −30 dB | 60 ms | 8 ms | 150 ms | Strip, Batch Fades 3 ms |
| Lead vocal, phrase edits | −50 dB | 300 ms | 40 ms | 250 ms | Separate, then edit |
| Room tone | −45 dB | 500 ms | 0 | 0 | Extract, Consolidate |
None of these are laws. A loud room, a close mic or a dynamic performer moves the threshold ten dB in either direction. The point is to start from a known place and adjust one slider at a time.
Two mistakes
Stripping across tracks with different levels. Strip Silence applies one threshold to the whole selection. A boom at −40 dB and a lav at −30 dB want different settings; do them separately, or the quieter one loses its soft lines.
Trusting the threshold on breaths. Breaths matter in dialogue and in vocals. If the editor wants them, raise the end pad rather than lowering the threshold; a lower threshold keeps breaths and also keeps the chair squeak.
How Pete does this
Session Pilot is a Mac app. You talk, and Punch In Pete works Pro Tools. Strip Silence is one of the things he runs directly, with the values you say.
Strip silence on the dialogue tracks at minus 45, half a second minimum, 30 milliseconds in front and 200 behind.
Batch fade all of that, 8 milliseconds in and out.
Rename the new clips Scene 12 dialogue, numbered.
The strip itself runs on your Mac the instant the sentence ends; the rename goes through the Batch Rename dialog, which Pete drives in a few seconds. He reads back the count when he is done. If you say the word "strip" and he is not sure he heard the threshold right, he reads it back and waits for "send it" rather than stripping at the wrong level. The threshold is still your call. He has no opinion about your breaths. He runs your SoundFlow commands by name too, so "kick folder router, then strip silence at minus 70" is one sentence.
Not just another bounce or session prep app. Pete is the best assistant you'll ever have.
Session Pilot launches 16 December 2026 for Mac. Everyone on the wait list gets launch pricing locked and a 14-day free trial.
Join the wait listSession Pilot is not affiliated with or endorsed by Avid Technology, Inc. Pro Tools is a trademark of Avid Technology, Inc. Menu paths refer to Pro Tools 2026.11; older versions may differ.